1-800-663-4209 | Your feedback matters, take a quick survey Website Feedback
FSV10-Series
100:1, 1/4 in Compression, 316ss, Electronic Proportioning Valves
Models In Stock
- Pulsewidth-Modulated Control Circuit
- Accepts 0 to 5 Vdc or 4 to 20 mA Setpoint Inputs
- Made of Corrosion- Resistant 316 and 416 SS/FKM
FSV10-Series
From
$
820.87
Models In Stock
Product Overview
- Approvals RoHS, CE
- Approvals Note EMC Directive 89/336/EEC EN55011:1991; Group 1, Class A EN50082-2:1995
- Cable Length 8 in
- Electrical Connection 9 - Pin D Connector
- Flow Rate Note Based on 10 psig (690 mbar) differential pressure.
- Height 1 in
- Input Control Signal 0 to 5 Vdc, 4 to 20 mA
- Leak Rate Under Vacuum less than 10^⁻9 cc He/s
- Length 3 in
- Material Construction Option N/A
- Materials, Wetted 316 Stainless Steel, 416 Stainless Steel, FKM
- Operating Pressure, Max 500 psi
- Operating Temperature, Max 50 °C
- Operating Temperature, Min 0 °C
- Pressure Type Differential
- Process Connection Size 1/4 in
- Process Connection Type Compression Fitting
- Process Temperature, Max 54 °C
- Process Temperature, Min -10 °C
- Response Time 500ms
- Supply Power Note 12 to 30 Vdc, 1 A @ 12 Vdc; 0.5 A @ 24 Vdc via 9-pin D connector or DC power jack
- Supply Voltage 12 to 30 Vdc
- Surface Temperature, Max 54 °C
- Turndown Ratio 100:1
- Valve Height 3.45 in
- Valve Length 3.25 in
- Valve Type normally closed
- Valve Width 1 in
- Width 3 in
The FSV10 Series electronic proportioning solenoid valves can control the flow of a wide variety of gases and liquids. The variablestroke electromagnetic valve is pulsed by the driver electronics, maintaining the correct magnetic flux level in the solenoid and holding flow at the level of the analog input setpoint signal. A TTL-level input allows the valve to be shut off regardless of analog setpoint signal.
The output power level of the driver electronics is jumper selectable for cooler, more efficient operation. The FSV10 Series requires 12 to 30 Vdc, supplied by the optional FSV-PW 110 Vac plug-in power supply or via the 9-pin D connector (included). These valves come with 8 inches of wire, which must be soldered to the 9-pin D connector.
SPECIFICATIONS
Turndown Ratio: 100:1
Response Time: 500 msec max
Fluid Temperature Range: -10 to 54°C (14 to 130°F)
Typical Valve Surface Temperature: 54°C (130°F) with 24 Vdc power input
Required Power Input (Not Included): 12 to 30 Vdc, 1 A @ 12 Vdc; 0.5 A @ 24 Vdc via 9-pin D connector or DC power jack
Connection: ¼" compression fittings
Setpoint Input Signal: 0 to 5 Vdc or 4 to 20 mA
Valve Dimensions: 87.6 H x 87.6 L x 25.4 mm W (3.45 x 3.25 x 1.00") including compression fittings
Driver Electronics: 7.62 W x 7.62 D x 25.4 mm H (3 x 3 x 1")
Materials in Fluid Contact: 316 and 416 SS, FKM O-rings
Maximum Pressure: 500 psig (3448 kPa)
Maximum Differential Pressure: 50 psid (345 kPa); 35 psid (241 kPa) for FSV15
Leak Integrity: 1 x 10-9 sccs; helium, individually tested
Ambient Temperature: 0 to 50°C (32 to 122°F)
CE Compliance: EMC Directive
89/336/EEC EN55011:1991; Group 1,
Class A EN50082-2:1995
The output power level of the driver electronics is jumper selectable for cooler, more efficient operation. The FSV10 Series requires 12 to 30 Vdc, supplied by the optional FSV-PW 110 Vac plug-in power supply or via the 9-pin D connector (included). These valves come with 8 inches of wire, which must be soldered to the 9-pin D connector.
SPECIFICATIONS
Turndown Ratio: 100:1
Response Time: 500 msec max
Fluid Temperature Range: -10 to 54°C (14 to 130°F)
Typical Valve Surface Temperature: 54°C (130°F) with 24 Vdc power input
Required Power Input (Not Included): 12 to 30 Vdc, 1 A @ 12 Vdc; 0.5 A @ 24 Vdc via 9-pin D connector or DC power jack
Connection: ¼" compression fittings
Setpoint Input Signal: 0 to 5 Vdc or 4 to 20 mA
Valve Dimensions: 87.6 H x 87.6 L x 25.4 mm W (3.45 x 3.25 x 1.00") including compression fittings
Driver Electronics: 7.62 W x 7.62 D x 25.4 mm H (3 x 3 x 1")
Materials in Fluid Contact: 316 and 416 SS, FKM O-rings
Maximum Pressure: 500 psig (3448 kPa)
Maximum Differential Pressure: 50 psid (345 kPa); 35 psid (241 kPa) for FSV15
Leak Integrity: 1 x 10-9 sccs; helium, individually tested
Ambient Temperature: 0 to 50°C (32 to 122°F)
CE Compliance: EMC Directive
89/336/EEC EN55011:1991; Group 1,
Class A EN50082-2:1995
PDFs & Manuals
Show Ratings & Reviews
Rated 1 out of
5
by
Anonymous from
Did not work with a water application.,
Device only controlled between 9.5 and 11.2 ma. otherwise it was either no flow, or sporadic flow outside of the range. Within the 9.5 to 11 ma there was no consistency. I was told by technical support that's normal. They would not take it back. My application was 175 to 300 psi H20 metering the flow between 40 and 110 ccm. I would not recommend this product.
Date published: 2021-08-09
What is the required gas filtration upstream of the valve (i.e. allowable particulates)?
Thank you for your inquiry. A recommended filter for the electronic valve is 20 to 50 microns
Date published: 2020-04-06
Can the compression fittings on this be removed/replaced?
Thank you for your inquiry. Yes, the compression fittings can be removed/replaced.
Date published: 2020-03-19
Can the valve be driven directly using a PWM signal instead of using the driver electronics? We are looking to replace an existing PWM driven valve (1Hz) and must have a drop-in replacement. Thanks!
Thank you for your inquiry! Unfortunately, this valve can not be driven directly using a PWM signal
Date published: 2021-06-09