Welcome to our new website, found an issue or bug? Please report it here
AHPF-HEATER
316 SS Inline Duct Heater up to 800 °F and 1.2 kW Power-Liq
Models In Stock
- 316 Stainless Steel Construction
- Air/Gas Flow up to 15 CFM
- Air/Gas Outlet Temperatures up to 800°F (430°C)
- Pressures up to 100 PSI*
AHPF-HEATER
From
$
557.83
Models In Stock
Product Overview
- Air Flow, Max 15 CFM
- Mounting Inline
- Outer Diameter 1.25 in
- Outlet Air Temperature, Max 430 °C
- Port 1 Size 3/8 in
- Port 1 Type NPT Male
- Port 2 Size 1/2 in
- Port 2 Type NPT
- Power Tolerance +5, -10%
- Sheath Material 316 Stainless Steel
The AHPF series heaters are used to heat low flows of air, gas, water, or aqueous solutions. Applications include those where clean air is necessary, as in laboratories and environmental testing areas. The stream of air is heated by passing over an enclosed heated surface rather than directly over resistance elements. This method assures that no foreign matter will enter the stream of flow. The AHPF series is also used as a miniature circulation heater for small volume liquids as in photographic developer solution, chemicals, dyes, and inks. Calculate the flow rate, temperature rise, or power requirement as described on page J-17. For heating liquids, use the formulas on pages Z-10 or Z-41. The Thermocouple “T†fitting AHPF-NPT12 can be used with the subminiature thermocouple probes and with the SSLK series stainless steel compression fittings (see the OMEGA Complete Temperature Measurement Handbook and Encyclopedia®) and with stainless steel compression fittings (model SSLK-18-14) to monitor or control temperature at the outlet of the AHPF series heaters.
SPECIFICATIONS
Cross Sectional Area: 0.152 sq. inches
Pressure Rating: Up to 100 PSIG
Wattage Tolerance: +5, -10% or better at the voltage specified
Outside Diameter: 11/4' (32 mm)
Inlet: Male 3/8' NPT
Outlet: 1/2' NPT
SPECIFICATIONS
Cross Sectional Area: 0.152 sq. inches
Pressure Rating: Up to 100 PSIG
Wattage Tolerance: +5, -10% or better at the voltage specified
Outside Diameter: 11/4' (32 mm)
Inlet: Male 3/8' NPT
Outlet: 1/2' NPT
| Model Number | Volts | Watts | Heated Length in (mm) | Watts/Inch* | Maximum CFM | Length in (mm) | Weight lb (kg) |
| 120 VAC Models | |||||||
| AHPF-061 | 120 | 400 | 4 (102) | 91 | 15 | 6 (152) | 1.00 (0.45) |
| AHPF-081 | 120 | 600 | 6 (152) | 94 | 15 | 8 (203) | 1.18 (0.54) |
| AHPF-101 | 120 | 1000 | 8 (203) | 120 | 15 | 10 (254) | 1.37 (0.62) |
| AHPF-121 | 120 | 1200 | 10 (254) | 115 | 15 | 12 (305) | 1.55 (0.70) |
| 120/240 VAC Models** | |||||||
| AHPF-062 | 120 240 | 100 400 | 4 (102) 4 (102) | 23 91 | 15 15 | 6 (152) | 1.00 (0.45) |
| AHPF-082 | 120 240 | 150 600 | 6 (152) 6 (152) | 23 94 | 15 15 | 8 (203) | 1.18 (0.54) |
| AHPF-102 | 120 240 | 250 1000 | 8 (203) 8 (203) | 30 120 | 15 15 | 10 (254) | 1.37 (0.62) |
| AHPF-122 | 120 240 | 300 1200 | 10 (254) 10 (254) | 29 115 | 15 15 | 12 (305) | 1.55 (0.70) |
| *Indicates Watts per inch of heated length. Use the table above to determine minimum required flow rates. **These air heaters can be operated on either 120 or 240 Volts. Specifications are shown for either 120 or 240 Volt operation. |
PDFs & Manuals
Show Ratings & Reviews
Rated 5 out of
5
by
Anonymous from
Good Purchase
Excellent Tool. Price is reasonable and it was delivered in a timely manner.
Date published: 2024-08-22
Rated 5 out of
5
by
Heat from
Hi power in-line heater
It is an excellent in-line heater.
Note that it requires proper gauge wiring and power control system.
Date published: 2020-12-26
can you confirm that these can be mounted vertically?
The AHPF can be mounted vertically because the heating element wires are held inside the tube and are not meant to move dependent on orientation.
Date published: 2024-01-31
Can this be used for preheating hydrogen and hydrocarbons?
Thank you for your inquiry. This heater can be used for these gases
Date published: 2023-07-15
Is the AHPF-121 (and for that matter, the CN-TOT controller I'd like to use with it) NRTL certified?
Thank you for your inquiry! Neither the AHPF-121 nor the CN-TOT are NRTL certified.
Date published: 2021-07-22
What are the materials that could come in contact with the air - Stainless? Also, can liquid flow through the system as well as air?
Thank you for your inquiry. Non-corrosive gases are acceptable. Non-viscous/corrosive liquids are acceptable.
Date published: 2023-01-12
Can you supply or can you recommend an air flow switch for the AHPF-062 (as recommended on the page 1 of the manual)?
When you have established your flow rate the Flow Engineering group can be contacted at flow@omega.com for the best Flow Switch recommendation for your specific application.
Date published: 2021-01-28
Can the heaters be set variably ie ramped up and down, or are they set to the listed value and are on/off?
Thank you for your inquiry. These heaters can be used with a temperature controller that has a ramp feature.
Date published: 2023-04-25
What is the minimum flow rate of each unit?
Thank you Gabriel B. The minimum flow rate of these units is 1 CFM.
Date published: 2023-06-22