Welcome to our new website, found an issue or bug? Please report it here
DP41-S-Series
High Performance Strain Meter, High Resolution 6-Digit Display
Models In Stock
- Compatible with Strain Gage Bridge Sensors or Ratiometric Voltage Sensors
- Adjustable Filtering Up to 13 Hz
- Displays Up to 999,999 Counts
- NEMA-4 Front Panel
DP41-S-Series
From
$
997.02
Models In Stock
Product Overview
- Accuracy ± 0.005 %
- Analog-to-Digital Technique Dual slope
- CMRR 120 dB
- Common Mode Voltage 1500 Vp per HV test
- Cutout Dimensions 1.772 x 3.622 in
- Display Note Red 6-digit, 14-segment, 13.7 mm (0.54") high; 4 alarm indicators
- Display Type LED
- Form factor 1/8 DIN
- Height 1.89 in
- Input Configuration Front panel buttons or via your computer
- Input Range Note 0 to 100 mV, 0 to 1V, 0 to 5V, 1 to 5V, 0 to 10V, 0 to 100V, ± 50 mV, ± 500 mV, ± 5V, ± 50V, 0 to 20 mA, 4 to 20 mA
- Input Type Single Ended, Strain
- Internal Resolution 15 bit
- Length 6.5 in
- Materials Polycarbonate
- Measurement Type Strain
- Mounting Panel
- NMRR 60 dB
- Number of Digits 6
- Number of Inputs 1
- Offset Adjustment 0 to 999999 or 0 to - 99999 programmable
- Operating Temperature, Max 50 °C
- Operating Temperature, Min 0 °C
- Polarity Unipolar/Bipolar, programmable
- Power Consumption 10 W
- Power Consumption Note 6 W Nominal, 10 W
- Reading Rate 3/s or 13/s, 60 Hz; 3/s or 12/s, 50 Hz
- Relative Humidity 95% RH non-condensing
- Resolution 15-bit
- Sampling Rate 13 Hz (13 updates/second)
- Sensor Break Protection Up-scale or down-scale, programmable
- Sensor Excitation 10 V at 30 mA; 24V at 25 mA
- SetPoint Outputs 4 Isolated Open Collector; Rated 150 mA at 1V Sink, 30V Open
- Span Adjustment 0.00001 to 500,000, programmable
- Span Temperature Coefficient ± 20 ppm
- Step Response 1 s to 99.9%
- Storage Temperature, Max 85 °C
- Storage Temperature, Min -40 °C
- Warm Up Time 50 min
- Weight 574 g
- Width 3.78 in
The OMEGA ® DP41-S indicators offer exceptional performance in a strain gage meter. The DP41-S has standard built-in excitation. The input range is selected via internal jumpers, and scaling to engineering units is performed using the front keypad. The DP41-S accepts strain gage bridge sensors and ratiometric voltage measurements. Programming the DP41-S is accomplished through the five front panel keypads. If the optional RS-232 or RS-485 communications are installed, the operator can remotely set all display parameters.
Examples of pricing for popular models is referenced in the "To Order" box. Use the "Part Number Builder" below to get pricing for all available models.
Examples of pricing for popular models is referenced in the "To Order" box. Use the "Part Number Builder" below to get pricing for all available models.
PDFs & Manuals
Show Ratings & Reviews
Rated 1 out of
5
by
17025 from
Save your money
1) No zero or Tate button. This is a basic function of nearly every instrument of this type.
2) No auto zero tracking. Again, a basic function found on every competitors equipment.
3) The scaling function simply does not work. Specifically, scaling with a known load will adjust span values while not changing zero. If your transducer has an output at no load (such as the case for any dead load), the only option is to put in an offset, which also changes span values.
When one of these shows up in our calibration lab, we push the customer to buy something else. These are an absolute joke.
Date published: 2022-01-13
Rated 3 out of
5
by
Adis from
Title
Not easy to use. some setups and wiring needs to be done before.
Date published: 2021-03-31
Rated 5 out of
5
by
madmagyar from
Long time OMEGA customer
Never been let down yet by any of their products, I have been purchasing from OMEGA for 20 plus years
Date published: 2017-05-02
Rated 5 out of
5
by
Jeru DS from
Works Great !
A great product. Easily operated. Would consider purchasing again.
Date published: 2024-12-19
Hi, Can I get some information on the RS232 command interface? The baud rate? Input/output data format?
Tayo, please see page 9-26 of the full manual for the Baud Rates: https://assets.omega.com/manuals/M1291.pdf
Date published: 2024-02-13
I have an older DP41-S with the older style RS-485 communications. I have not been able to establish communications with it. I have a few other things to try, but if it turns out the communication board is bad, can I buy a replacement RS-485 board?
Thanks for your question. Our Tech Support team has connected with you and a manual has been sent per your request. If there is anything else we can help you with, please contact our Tech Support team anytime, thank you.
Date published: 2019-04-25
Does the DP41-S Strain Gage Indicator have an up-to-date digital output? I'm aware of option DP40-B, however its 300-19,200 baud output is somewhat antiquated? Higher baud rate available? USB output available?
There are no updates on the digital output of DP41-S. There is also no USB option for this display. We suggest you look at our DP8EPT Series displays. They have USB communications as a standard feature.
Date published: 2021-01-02
Are the mating electrical connectors for the display available for purchase separately? If not, can you provide the part numbers of the mating connectors so they can be purchased from an electrical supplier?
Thank you for your inquire.
Yes they are available.
We have 3 different types for input output and power.
Please contact us direct to discuss the connectors' that you are in need of.
Date published: 2021-05-28
Beside two pages PDF manual. Do you have full IO&M manual for the meter DP41-S-AR4. if yes, can you send to me?
Thank you for you question?
Please email pressure@omega.com We will be more then happy to assist you with this.
Date published: 2020-04-07
I did not find this code DP462 ?
The DP460 Series is an older display that has been discontinued for several year. The most current display the would take it's place is either the DP8PT (4 Digits) or the DP8EPT (6 Digits).
Date published: 2020-04-17
LC8250-625-40K is said to be compatible with DP41-S, the meter is to measure forces in lbs not strains, is this correct?
The DP41-S has a 6 digit scalable display so you can read directly in pounds force by scaling it to read 0 to 40000 count across the output signal from the load cell.
Date published: 2021-10-21
will it shorten the life of a DP41 meter if the input voltage is 128
Specification calls out a maximum of 126.5 VAC for the 115VAC powered version. We have no data on how 128 VAC would effect the unit
Date published: 2022-02-25