Welcome to our new website, found an issue or bug? Please report it here
DP20-Series
Panel Meter - 1/8 in DIN, Temperature, Process
Models In Stock
- Fast Access Menu—Front Key Access to Modify the Alarm Setpoints and Max/Min Memory
- External Control Function—Contact at Multifunctional Terminal 5 (Second Scaling, Decimal Point Change, ‘Hold’ the Reading or Activate the Max/Min Memory)
- Automatic, Power Saving Eco Mode
- Alarms 1 or 2, Independent, Configurable as Max/Min, with Setpoint and Hysteresis
DP20-Series
From
$
152.24
Models In Stock
Product Overview
- Analog Input Note 4 to 20 mA, 0 to 10 Vdc (+15 Vdc excitation voltage configurable at terminal 5)
- Applications Assembly Line, Control Panel, Laboratories and Scientific
- Decimal Points Configurable
- Digit Size 14 mm
- Display Range -1999 to 9999
- Display Type 3.5 Digit LED
- Electrical Connection Screw Terminal
- Enclosure Ratings IP65, NEMA Type 4
- Form factor 1/8 DIN
- Input Type Thermocouple, RTD, Thermistor, Current, Voltage, DC or AC, Resistance, Frequency
- Measuring Range Thermocouple: Type K: -100 to 1350 °C;Type J: -100 to 1200 °C;Type E: -100 to 1000 °C;Type N: -100 to 1300 °C;Type L: -100 to 900 °C;Type R: 0 to 1768 °C;Type S: 0 to 1768 °C;Type T: -100 to 400 °C;Type C: 0 to 2300 °C;Type B: 700 to 1820 °C ;RTD: Pt100(3 wires): 200 to 700 °C ;Pt100(2 wires): 200 to 700 °C ;Pt500: -150 to 630 °C ;Pt1000: -190 to 630 °C ;Ni100: -60 to 180 °C ;Ni200: -60 to 120 °C ;Ni1000: -60 to 180 °C ;Resistance: 0 to 5K: from 9999 to -1999;0 to 50K: from 9999 to -1999;Potentiometers Nominal Value: 500 R to 20 K: from 9999 to -1999;Frequency: 15 Hz to 100 Hz: from 9999 to -1999; Signal Ranges: AC Voltages and AC Currents: 600 Vac, 200 Vac, 20 Vac, 2 Vac, 200 mVac, 60 mVac, 5 Aac, 20 mAac (True RMS measure) (accepts phase-neutral and phase-phase measure) ;DC Voltages and DC Currents: ± 600 Vdc, ± 200 Vdc, ± 20 Vdc, ± 2 Vdc, ± 200 mVdc, ± 60 mVdc, ± 5 Adc, ± 20 mAdc;Refer Tables for more information; Analog Input: 4 to 20 mA, 0 to 10 Vdc
- Number of Inputs 1
- Operating Temperature, Max 50 °C
- Operating Temperature, Min 0 °C
- Power Consumption 2.5 W
- Probe Type Resistive ‘Pt’ Probes: Pt100 with 2 and 3 wires, Pt500, Pt1000 Resistive ‘Ni’ Probes: Ni100, Ni200, Ni1000 Resistive NTC Probes: See table at page 4 Resistive PTC Probes: Families KTY-121, KTY-210 and KTY-220
- Reading Rate 3/sec
- Resistance Measurement Range Up to 20 KΩ
- Response Time <300 ms. (0 % to 99 % of signal)
- Sampling Rate 3 Hz (3 updates/second)
- Sensor/Transmitter Power 15 Vdc
- Span Temperature Drift 150 ppm/°C
- Supply Power Note 18 to 265 Vac/dc (isolated 1500 Veff @ 60 seconds)
- Supply Power Type AC/DC
- Supply Voltage 18 to 264 Vac/Vdc
- Thermal Effects 150 ppm/°C
- Thermocouple Type J, K, T, E, R, S, B, C, N, L
- Weight 150 g
OMEGA’s DP20 series new universal panel meter delivers high performance in a 1/8 DIN size for panel mount, and integration in a wide range of applications. The DP20 accepts universal inputs, including thermocouple, RTD, process (mA & Vdc), resistance, and true RMS voltage and current. By configuration, it will work as an AC and DC voltmeter (up to 600 V) and AC and DC ammeter (up to 5 A) offering application flexibility for process control and industrial requirements. A single universal power supply allows this unit to be suited for global use.
Introduce Omega DP20 Series The optional relays, analog output, and Modbus® RTU serial communications provide customization, control and communication capability. Additional features of the economical DP20 panel meter include scaling, NEMA 4 (IP65) protection, and programmable decimal points.
Specifications
Digits: 4
Reading: 9999 / -1999
Decimal Point: Configurable
LED Color: Red
Digit Height: 14 mm (0.55")
Accepted Signal Ranges: See tables on pdf page 4 for more information
AC Voltages and AC Currents: 600 Vac, 200 Vac, 20 Vac, 2 Vac, 200 mVac, 60 mVac, 5 Aac, 20 mAac (True RMS measure) (accepts phase-neutral and phase-phase measure)
DC Voltages and DC Currents: ±600 Vdc, ±200 Vdc, ±20 Vdc, ±2 Vdc, ±200 mVdc, ±60 mVdc, ±5 Adc, ±20 mAdc
Thermocouples: K, J, E, N, L, R, S, B, T and C (automatic cold junction compensation)
Probes:
Resistive ‘Pt’ Probes: Pt100 with 2 and 3 wires, Pt500, Pt1000
Resistive ‘Ni’ Probes: Ni100, Ni200, Ni1000
Resistive NTC Probes: See table at page 4
Resistive PTC Probes: Families KTY-121, KTY-210 and KTY-220
Process: 4/20 mA, 0/10 Vdc (+15 Vdc excitation voltage configurable at terminal 5)
Resistances: Ranges 0/5 K and 0/50 K
Potentiometers: With nominal values from 500 R up to 20 K
Thermal Drift Offset+Span: 150 ppm/ºC
How to Open/Close the Omega DP20 Housing Readings: 3 readings/ second
Refresh: 3 readings/ second
Response Time: <300 mSec. (0 % to 99 % of signal)
Power ‘U’: 18 to 265 Vac/dc (isolated 1500 Veff @ 60 seconds)
Output and Control Options:
1 or 2 Relays: 1 Analog output 4/20 mA isolated
1 Modbus RTU isolated serial output
Protection: NEMA 4 (IP65)
Consumption (Normal Mode): <1.0 W (meter only) <2.5 W (meter with options)
Consumption (‘Eco’ Mode): <0.3 W (meter only) <1.5 W (meter with options)
Connections: Plug-in screw terminals
Weight: <150 g (5.3 oz)
Operation Temperature: 0 to 50ºC (32 to 122ºF)
Specifications
Digits: 4
Reading: 9999 / -1999
Decimal Point: Configurable
LED Color: Red
Digit Height: 14 mm (0.55")
Accepted Signal Ranges: See tables on pdf page 4 for more information
AC Voltages and AC Currents: 600 Vac, 200 Vac, 20 Vac, 2 Vac, 200 mVac, 60 mVac, 5 Aac, 20 mAac (True RMS measure) (accepts phase-neutral and phase-phase measure)
DC Voltages and DC Currents: ±600 Vdc, ±200 Vdc, ±20 Vdc, ±2 Vdc, ±200 mVdc, ±60 mVdc, ±5 Adc, ±20 mAdc
Thermocouples: K, J, E, N, L, R, S, B, T and C (automatic cold junction compensation)
Probes:
Resistive ‘Pt’ Probes: Pt100 with 2 and 3 wires, Pt500, Pt1000
Resistive ‘Ni’ Probes: Ni100, Ni200, Ni1000
Resistive NTC Probes: See table at page 4
Resistive PTC Probes: Families KTY-121, KTY-210 and KTY-220
Process: 4/20 mA, 0/10 Vdc (+15 Vdc excitation voltage configurable at terminal 5)
Resistances: Ranges 0/5 K and 0/50 K
Potentiometers: With nominal values from 500 R up to 20 K
Thermal Drift Offset+Span: 150 ppm/ºC
Refresh: 3 readings/ second
Response Time: <300 mSec. (0 % to 99 % of signal)
Power ‘U’: 18 to 265 Vac/dc (isolated 1500 Veff @ 60 seconds)
Output and Control Options:
1 or 2 Relays: 1 Analog output 4/20 mA isolated
1 Modbus RTU isolated serial output
Protection: NEMA 4 (IP65)
Consumption (Normal Mode): <1.0 W (meter only) <2.5 W (meter with options)
Consumption (‘Eco’ Mode): <0.3 W (meter only) <1.5 W (meter with options)
Connections: Plug-in screw terminals
Weight: <150 g (5.3 oz)
Operation Temperature: 0 to 50ºC (32 to 122ºF)
PDFs & Manuals
Show Ratings & Reviews
Rated 4 out of
5
by
Bob52 from
Nice meter for the price
My application was to display rpm on a mill, where the speed control produced a 0-10v signal that corresponded to 0-4500 rpm. The DP20 was easy to program for that use and works well. Be aware the case is very thin, and the clamps are plastic so it's not as robust as you might be used to.
Date published: 2018-04-15
Rated 4 out of
5
by
wstein25 from
Does the job but ...
I may be a bit dense about these things, but I found the nested menu/push button configuration complicated. In the end I got the scaling and alarms set up as I needed, but I'm not sure I could explain how I did this. But, in the end it works well as advertised.
Date published: 2018-05-06
Rated 5 out of
5
by
ruf tech from
good display
liked the easy installation. easy to program with only three buttons. easy to see display from a distance. the plastic bracket was a bit flimsy but it did the job.
Date published: 2021-02-08
Rated 4 out of
5
by
Nick I from
Good value part
Decent quality for the cost. Relays are a nice addition.
Date published: 2021-02-04
Rated 4 out of
5
by
scn01 from
works good great value
setup was a small challenge but meter worked as described and has a bright display
Date published: 2018-01-16
Rated 5 out of
5
by
undisclosed from
great product, works as advertised
great product, works as advertised, priced appropriately
Date published: 2024-09-20
Rated 5 out of
5
by
Angela Clark from
Customer Service Specialist
Super fast quoting and super fast shipping. Parts are always in stock.
Date published: 2024-05-21
Rated 5 out of
5
by
Wm Ed from
Panel Meter
I found just what I was looking for with the Omega Engineering DP20-M1 panel meter. Simple installation and easy to configure. For support, Omega Engineering has a very good manual online for this unit which is great.
Date published: 2024-03-21
we have this controller hooked to a PX119-1K. We have set the scale to D.Lo to 0 and D.Hi to1000. unit still reads -250. we have gone through the manual many times and set it up both ways for 4-20mA. - Please help
Assuming you are using the internal excitation on-board the DP20. Jumper "S" on the PCB should be on position "D" Jumper "T" should be bridging pins 1 & 2. The positive lead from the sensor should be on Term# 5 of the Input terminal block. The negative lead should be on Term#2. Verify that you have the 15VDC excitation be measuring between terminals 5 and 4 with a DC voltmeter. Make sure you are choosing Process input and 4/20 mA range.
Date published: 2023-02-13
Do you sell the small Blue retainer clicks separately? Our had gotta brittle and the meter doesn't mount well. If you do, please post a part number. Thanks Jeff at Teledyne Marine.
Thank you for your inquiry. Please send your request to sales@omega.com
Date published: 2020-05-18
Hi, I have an omega DP20 meter, question, is it a need to drop a transient voltage suppressor across my signal inputs to protect against voltage spikes or is the DP20 capable of handling such an occurrence? Thanks
Thank you for your inquiry. Voltage Suppressor is not required for voltage input signals.
Date published: 2022-05-20
I have a failed NEWPORT IDP-0/E and was wondering if this would be an equivalent replacement when used with an input of 4-20 mA. Meter is only used to display values. Also can this be used outdoor exposed enclosure?
Thank you for your inquiry. The DP20 would have to be in a weatherproof enclosure to ensure long-lasting use.
Date published: 2020-12-04
I can't seem to figure out how to scale the signal to have numbers AFTER the decimal point. I am using an externally powered PX119 set up for 4-20mA. I am measuring psi from 0-30, and I would like the display to read 9.45 psi rather than just 9 or .09 etc
Dear AdamB, thank you for contacting Omega Engineering. For scaling the DP20 to read from 0.00 through 30.00 psi, assuming you have the wiring and the internal jumpers correct, keep pressing the little square button, till you see "SCAL" , you will see DP (Decimal Point) : Set the decimal point in the middle, so XX.XX . Your D.Lo should be 00.00 and D.Hi should be 30.00. You should then be reading from 00.00 to 30.00.
For more information please see page 19 of the manual: https://assets.omega.com/manuals/M5668.pdf
Date published: 2023-02-03
I am using this with thermocouples, is the meter calibratable?
Thank you for your inquiry. This unit is not calibratable.
Date published: 2024-03-22
I see that there is a place for "units". Is this digital that needs to be programmed? Or is this just a label, and does it come with a sheet of labels? I will be needing RPM and Amps
Thank you for your inquiry. This device does not display units of measure digitally. It is the user responsibility to interpret the units of the value displayed.
Date published: 2023-09-28
Can the relays switch DC? The manual only mentions up to 250VAC. I would be switching 24VDC
The only rating for the relays on the DP20 is for 250 VAC at 8 amps. There is not any DC Voltage rating.
Date published: 2020-12-10