HTS-HANI-CLAMP-P

Industrial Plastic Pipe Clamp HANI Temperature Sensor

(0)

Models In Stock

Non-invasive temperature measurement
Installation in seconds, no tools required
Clamps to outside of pipe, measures fluid inside of pipe
Accuracy comparable to an invasive sensor, ± 1.5°C

See Product Overview

HTS-HANI-CLAMP-P

From ^C$ 1 115.68

Models In Stock

Shop Models

2 Variations available

See all series options below

Data Sheet

Product Overview

Accuracy ± 1.5 °C (± 2.7 °F)
Accuracy Note ± 1.5°C from factory and improved accuracy possible with in-situation 1 or 2-point calibration
Applications Aeronautics and Aerospace, Air and HVAC, Building and Maintenance, Chemicals, Clean Water and Purified Solutions, Energy Generation and Distribution, Fluid Measurement and Control, Food and Beverage, Fuel and Gas, General Purpose, Heat and Energy Systems, Hydraulic and Pneumatic Systems, Industrial and Manufacturing, Laboratories and Scientific, Materials and Surfaces, Medical, Office and Commercial, Oils, Pharmaceutical, Waste Management
Base Mounting PVC, CPVC, PP, PFA
Electrical Connection M12 8 pin Female
Enclosure Ratings IP65
Height 2.03 in
Length 2.53 in
Loop Resistance (Vsupply -8V)/0.24 A
Materials Nylon, Silicone, Brass, Stainless Steel
Media Compatibility Water, Water-based fluids
Mounting Clamp
Operating Temperature, Max 40 °C
Operating Temperature, Min 0 °C
Output Detail 4 to 20 mA User scalable analog output, default scaling 0-100°C
Output Signal Current
Process Temperature, Max 100 °C
Process Temperature, Min 0 °C
Response Time t63: 30 sec; t90: 60 sec
Supply Power Note 8 VDC - 28 VDC (loop powered) Max Loop Resistance: Rmax (Ω)= (Vsupply -8V)/0.24 A
Supply Voltage 8 to 28 Vdc
Width 2.38 in

Ease of Installation

Install your HANI™ Clamp Sensor in seconds

Omega’s innovative clamp-on design makes sensor installation easy. Unlike invasive sensors, the HANI™ Clamp Sensor mounts to the outside of an industrial plastic pipe and measures the temperature of the process media inside the pipe.

• No drilling
• No cutting
• No downtime

Need to relocate the sensor? Un-clamp and go!

High Accuracy & Fast Response Times

Performs like an invasive sensor.

Omega’s patent pending Hybrid Temperature Sensing platform uses multiple sensors and a proprietary algorithm to achieve steady state accuracy comparable to invasive sensors and faster response times than surface sensors.

• Accuracy for industrial plastic pipes: ± 1.5°C

Industrial pipes have a wide variety of tolerances, surface finishes, and coatings which can affect the accuracy. An in-situation user calibration can be done to improve the accuracy for your specific application. Use the free Omega Sync software to do a 1 or 2-point calibration with the HANI™ Clamp Sensor and an in-place immersion sensor. See the user manual for additional details.

Non-Invasive & Non-Contact Operation

No penetration, no risk of contamination

The HANI™ Clamp Sensor never comes into contact with the process media flowing through the pipe. There is no risk of buildup, sensor wear or breakage from high flow rates, corrosive/abrasive liquids, wake frequency and water hammer.

Ensure you select the right sensor for your system

Industrial pipes have different outer and inner diameters, make sure you pick the correct sensor for your application. The HANI Clamp Sensor is factory set for schedule 40 industrial pipes. To adjust to a different pipe schedule please refer to the user’s manual.

Pipe Type	OD (Outer Diameter)	ID (Inner Diameter)	Wall Thickness	Schedule
1.0” Industrial Pipe	1.315”	1.049”	0.133”	40
2.0” Industrial Pipe	2.375”	2.067”	0.154”	40
1.0” Industrial Pipe	1.315”	0.957”	0.179”	80
2.0” Industrial Pipe	2.375”	1.939”	0.218”	80