Welcome to our new website, found an issue or bug? Please report it here
HTS-HANI-CLAMP-I
Industrial Metal Pipe Clamp HANI Temperature Sensor
Models In Stock
- Non-invasive temperature measuring fluid inside the pipe
- No process downtime or welding needed for install
- Installation in a matter of seconds with clamping mechanism
- As accurate as an invasive sensor, ± 0.50 to ± 1.0°C accuracy
HTS-HANI-CLAMP-I
From
C$
990.16
Models In Stock
Product Overview
- Accuracy ± 0.5 °C (± 0.9 °F)
- Accuracy Note ± 1.0°C from factory and improved accuracy to ± 0.5°C possible with in-situation 1 or 2-point calibration
- Applications Industrial and Manufacturing
- Base Mounting Metal Pipe
- Electrical Connection M12 8 pin Female
- Enclosure Ratings IP65
- Height 2.03 in
- Length 2.53 in
- Loop Resistance (Vsupply -8V)/0.24 A
- Materials Nylon, Silicone, Brass, Stainless Steel
- Media Compatibility Water, Water-based fluids
- Mounting Clamp
- Operating Temperature, Max 40 °C
- Operating Temperature, Min 0 °C
- Output Detail 4 to 20 mA User scalable analog output, default scaling 0-100°C
- Output Signal Current
- Process Temperature, Max 100 °C
- Process Temperature, Min 0 °C
- Response Time t63: 5 sec ; t90: 10 sec
- Supply Power Note 8 VDC - 28 VDC (loop powered)
- Supply Voltage 8 to 28 Vdc
- Width 2.38 in
Ease of Installation
Install your HANI™ Clamp Sensor in seconds
Omega’s innovative clamp-on design makes sensor installation easy. Unlike invasive sensors, the HANI™ Clamp Sensor mounts to the outside of an industrial metal pipe and measures the temperature of the process media inside the pipe.
- • No drilling
- • No welding
- • No downtime
Need to relocate the sensor? Un-clamp and go!
High Accuracy & Fast Response Times
Performs like an invasive sensor.
Omega’s patent pending Hybrid Temperature Sensing platform uses multiple sensors and a proprietary algorithm to achieve the same accuracy and fast response times as state-of-the-art invasive sensors without the cost and risk.
• Accuracy for industrial metal pipes: ± 0.5 to ± 1.0℃
•Response time = 5 sec (Ï„63) / 10 sec (Ï„90)
Industrial pipes have a wide variety of tolerances, surface finishes, and coatings which can affect the accuracy. An in-situation user calibration can be done to improve the accuracy for your specific application. Use the free Omega Sync software to do a 1 or 2-point calibration with the HANI™ Clamp Sensor and an in-place immersion sensor. See the user manual for additional details.
Non-Invasive & Non-Contact Operation
No penetration, no risk of contamination
The HANI™ Clamp Sensor never comes into contact with the process media flowing through the pipe. There is no risk of buildup, sensor wear or breakage from high flow rates, corrosive/abrasive liquids, wake frequency and water hammer.
Ensure you select the right sensor for your system
Industrial pipes have different outer and inner diameters, make sure you pick the correct sensor for your application. The HANI Clamp Sensor is factory set for schedule 40 industrial pipes. To adjust to a different pipe schedule please refer to the user’s manual.
| Pipe Type | OD (Outer Diameter) | ID (Inner Diameter) | Wall Thickness | Schedule |
| 1.0” Industrial Pipe | 1.315” | 1.049” | 0.133” | 40 |
| 2.0” Industrial Pipe | 2.375” | 2.067” | 0.154” | 40 |
| 1.0” Industrial Pipe | 1.315” | 0.957” | 0.179” | 80 |
| 2.0” Industrial Pipe | 2.375” | 1.939” | 0.218” | 80 |
Common Applications
New and retrofitting existing systems
Lower the total cost of ownership and reduce contamination risk without sacrificing performance by upgrading to a HANI™ Clamp Sensor.
Quality control & ad-hoc sensing
Clamp-on the sensor in seconds and connect to your laptop or PC for readings anytime - anywhere.
Verify existing invasive sensors
With accuracies comparable to most state-of-the-art invasive sensors, the HANI™ Clamp Sensor can easily be placed next to an invasive sensor to verify the accuracy or determine the drift of the invasive sensor.
PDFs & Manuals
Software & Drivers
Show Ratings & Reviews
Hani noninvasive clam temperatrue sensor. Q: 1. any experience within ice cream pipe lines (i.e. some examples re pipe chil)? 2. how does it deal with startup issues (i.e. environmental frost build up and product build up at inside of pipe work)?
Hi RTFeenstra,
Operating range is limited to 0 C on the low end. Unit will provide temperature of the media at the site of the sensor. Please forward request to TEMP@OMEGA.COM for more details.
Best regards,
OMEGA
Date published: 2022-10-21
Will this device measure the temperature of oil inside a pipe?
Hi Mark1342,
For media other than water based, please forward request with detail to TEMP@OMEGA.COM.
Best regards
OMEGA
Date published: 2023-05-05
Will this measure a gas temp inside a pipe.
Thank you for your inquiry. This device measures liquid media only.
Date published: 2022-09-14
RoHS 2015/863 - View Certificate
CE Approved
UKCA
