Welcome to our new website, found an issue or bug? Please report it here
PS-SNUBBERS
Pressure Snubbers to Protect Against Pressure Surges
Models In Stock
- Protects Transducers, Gauges and Switches from Pessure Spikes, Surges and Water Hammer
- Available in 1/8, 1/4, or 1/2 NPT Fittings
- Three Different Porosity Ratings Suitable for Most Media
- All Stainless Steel Construction
PS-SNUBBERS
From
C$
23.26
Models In Stock
Product Overview
- Materials, Wetted 316 Stainless Steel
- Snubber Type Poros Metal Disk
PRESSURE SNUBBER - for dampening and filtering. The snubber has a porous metal disc available in three standard grades of porosity. Due to the large filter surface the snubber has less tendency to clog than orifice type devices. The housing is 303SS and the filter disc is 316SS with a maximum PSI rating of 10 000 at 25°C. (PS-8 series 5000 PSI)
Please note that the finish of pressure snubbers may vary. The flat surfaces on snubbers you receive may have a smooth and machined appearance or they may have a textured, shot-peened appearance. These are merely cosmetic differences that do not affect the functionality and performance of the product.
PDFs & Manuals
Show Ratings & Reviews
Rated 5 out of
5
by
Acer from
Presurre snubber
This is a beautifully made and designed product at a very reasonable price.
It works as advertised. My use is in the manifold pressure measuring system of a Garmin engine monitor.
The pressure reading is very steady with the addition of the Omega snubber. It should be required with all Garmin engine monitors.
Date published: 2017-02-20
Rated 5 out of
5
by
Recreational from
Perfect for my boost gauge
Fixed my flutter in my boost gauge installed on my 2001 cummins powered RV
Date published: 2017-06-22
Rated 4 out of
5
by
Rvator from
Stable
Used to stabilize manifold pressures that were fluctuating over two inches. Brought it down to .1 movement.
Date published: 2018-02-25
Rated 5 out of
5
by
JonS from
Works great for diesel boost gauges
Works great with Autometer boost gauges to stop the needle from flopping around from cylinder pulse
Date published: 2025-02-01
Rated 5 out of
5
by
PeteS from
Good quality piece
Very nice piece. Not much to say about it, Works good.
Date published: 2024-08-30
Rated 5 out of
5
by
Jake S from
Pressure Snubber
Part is as expected, arrived on time, and seems to be operating as designed.
Date published: 2023-04-03
Rated 5 out of
5
by
Steven E from
Reliable part
Simple. Does what its supposed to do and it is high quality.
Date published: 2023-03-17
Rated 5 out of
5
by
Anonymous from
Pressure spikes
These are essential for discharge pump pressures on any sensor. They work wonderfully.
Date published: 2023-03-17
For a pressure transducer operating in a mixed environment (gas and liquid) what would be the best choice?
Thank you for your inquiry, the PS-4G would work best in this application
Date published: 2022-02-07
can a PS-4G be cleaned if it is contaminated
Thank you for your inquiry, due to the cost of the PS-4G we would recommend that you replace it.
Date published: 2022-09-23
Is there a CV associated with these, can it be calculated ?
There is no CV associated with this snubber. No information on calculating CV available
Date published: 2024-02-16
Does it matter which direction the PS-4G snubber is installled in a Manifold Pressure Line?
Thank you for your inquire.
The snubber needs to be in the positive direction. It will not work if its used in a vacuum.
Hope this was helpful
Date published: 2022-10-31
Does it matter if the positive pressure flows into the male end, or the female end?
Positive flow should be going from female end outward
Date published: 2022-10-31
Are your Stainless steel snubbers lead free?
Our snubbers are made of high quality stainless steel. There should be no lead present.
Date published: 2023-03-31
What is the burst pressure of the PS-4E ?
Joe G, per the spec sheet the housing is 303SS and the filter disc is 316SS with a maximum PSI rating of 10 000 at 25°C. (PS-8 series 5000 PSI)
Date published: 2024-12-05