Welcome to our new website, found an issue or bug? Please report it here
PLM-Series
Polyimide Flexible Heater with Polyimide Strain Relief
Models In Stock
- All polyimide strain relief and insulation
- Optional pressure sensitive adhesive models
- Temperature ranges from -57°C (-71°F) to 232°C (450°F)
- Non-magnetic heating element
PLM-Series
From
C$
81.93
Models In Stock
Product Overview
- Bend Radius, Min 0.032 in
- Dielectric Strength 1250 Vac
- Heater Material Polyimide
- Heater Thickness Note .01“, .strain relief max is 08” (.10” for heaters ≥ 3 Amp)
- Lead Length 12 in
- Lead Length Note PTFE Insulated, 12” ±0.4" Length, UL10109, 22 AWG (UL1332, 16 AWG for heaters ≥ 3 Amp)
The PLM-Series polyimide flexible heaters are offered in a variety of sizes and watt densities. These flexible heaters are polyimide insulated with a polyimide strain relief designed to be used in various environments and hard to reach places. They feature a non-magnetic heating element and watt densities of 2.5 W/in2, 5 W/in2 or 10 W/in2.
PLM-Series heaters have a thickness of 0.01 for a low profile wherever they are installed. Self-adhesive options available for easy and simple installation and eliminate the need for clamping. Temperature ranges from -40°C (-40°F) to 149°C (300°F) for self-adhesive models and -57°C (-71°F) to 232°C (450°F) for no adhesive models.
The PLM-Series heaters are made of polyimide for increased flexibility for curved surfaces and chemical resistivity. The thin nature of these heaters makes them ideal for tight spaces and good for applications such as hot plates, airplanes, storage tanks, beakers, trays, drying chambers and more.
PDFs & Manuals
Show Ratings & Reviews
Rated 5 out of
5
by
KP Precision from
Hard to find easy to order.
Tough to find product very limited options apart from Omega. Long order lead time came in earlier.
Date published: 2024-05-17
Can I use this with rolling itself (overlapped it self) ?
Thank you for your inquiry. 'Hotspots' caused by opposing heat transfers when a heater is overlapped with itself will cause it to fail.
Date published: 2023-07-17
Can you tell me the type of metal (copper, other allow) that is used for the heater traces inside? Thank you.
Hi Inflipant,
Thank you for the inquiry. Please forward this request to TEMP@OMEGA.COM
Best regards
OMEGA
Date published: 2022-05-19
What is the outgas specification for silicon patch used in KHLVA-202/2-P heater
Thank you for your inquiry. Unfortunately, we do not have this information readily available. Please send an email to heaters@dwyeromega.com
Date published: 2024-11-28
Do the leads come out from the side labelled 'width' or 'length'?
Thank you for your inquiry. The leads come out from the side labeled as Width.
Date published: 2024-07-03
Can 28V DC PLM series heater work fine at 12v DC? at 12 v it can drain more current as compared to 28v, As P=VI.
Hi Moon,
Thank you for the inquiry. The PLM can operate on 12 VDC. But the power rule is also P=V(squared)/ Resistance. If the voltage was cut in half the P value would be a square of the difference ( 1/4)
Best regards
OMEGA
Date published: 2024-01-30
Is it compatible with 24VDC power input? Can I run it with 24VDC?
Thank you for your inquiry. You may use a lower rated voltage but be aware that you will not reach the maximum total wattage rated at 28V.
Date published: 2024-01-30
Can these be cut ?
Hi Rolling123,
Thank you for the inquiry. These cannot be cut.
Best regards
OMEGA
Date published: 2021-12-03
Can kapton heaters be submersed in deionized water? I am looking to heat a gel to 37C from the inside. The gel is poured in liquid form in di Water at 50C, with the heater in it, then the gel sets at room temperature.
Thank you for your inquiry. These heaters are not suitable for water immersion. Danger Of Electrical Shock.
Date published: 2024-01-31