Welcome to our new website, found an issue or bug? Please report it here
SA1-RTD-B-series
Self-Adhesive Polyimide Fast Response RTD Surface Sensors, Class B Accuracy
Models In Stock
- 100 Ohm Thin Film DIN Platinum Class “B” (± 0.12 Ohms, ± 0.30°C at 0°C) Accuracy Standard
- Silicone Adhesive rated to 260°C (500°F)
- Temperature Range -73C to 260°C Continuous, 290°C (554°F) Short Term Operation When Installed with OMEGABOND Air Set Cements
- Stocked in 1m (40”) Lengths
SA1-RTD-B-series
From
C$
268.22
Models In Stock
Can't find the right model?
Use our custom configurator to fine tune your product
Product Overview
- Accuracy Class B
- Accuracy Note 100 Ω Thin Film DIN Platinum Class “B” (± 0.12% at 0°C) Accuracy Standard
- Insulation PFA
- Mounting Class DIN Platinum
- Nominal Resistance 100 Ω
- Pack Size 3
- Process Temperature, Max 260 °C
- Process Temperature, Min -73 °C
- Response Time In Water Immersion : <0.9 sec ; On a Hot Plate: <2 sec
- Temperature Coefficient 0.00385 Ω/Ω/°C
- Temperature Coefficient Note α = 0.00385 Ω/Ω/°C
- Temperature Sensor Type RTD
- Wire Gauge 26 AWG
The SA1-RTD is a surface temperature sensor that can be applied to most clean, dry surfaces. Just peel off the release sheet on the bottom of the sensor and the silicone adhesive bonds the sensor to the surface, no cements or epoxies to mix, apply and cure.
The thin design of the SA1-RTD minimizes the effects of having the sensor attached to the surface of interest. Containing a thin film platinum sensing element, the SA1-RTD resistance is not affected by mounting to curved surfaces. With a fast thermal response time, the SA1-RTD will quickly respond to changes in temperature for fast, reliable measurements.
PDFs & Manuals
Accessories
Show Ratings & Reviews
Rated 3 out of
5
by
RZ17 from
RTD sensors kit
Used with RDXL65D - 6 channel Temperature Data Logger with Touch Screen.
RTD sensors are OK, but using with stereo(3-pole) 3.5 mm connectors (RDXL65D) is a bad idea.
Stereo connectors DO Not provide reliable low resistance contact, which shows as inconsistent measurement results.
Date published: 2017-04-10
Rated 5 out of
5
by
RaymondBL from
Great temperature probes
Omega's RTDs have always been robust and well made. The self adhesive ones are nice for the testing I want to do.
Date published: 2024-07-15
Rated 5 out of
5
by
MOTEDE from
RTD
excellent product and easy to use RTD. great company to work with.
Date published: 2023-09-18
Rated 5 out of
5
by
Devlin from
Just what we needed
Just what we needed, shipped on time and well packaged.
Date published: 2023-02-23
Hi I purchased a pack, I received it alread, Packing Slip: 834570 Order: HC00491380, Orthosensor INC Can you please provide product DATA SHEET, and if available IFU intructions for use? mainly I need to know what each of the black,black,red wires are?
The only DATA SHEET that Omega can offer for the SA1-RTD-B series can be found by clicking Data Sheet (PDF) underneath the bullet points on the link included. We have no formal wiring diagrams but the way that RTD is wired is that both Black wires are attached to one side of the sensing element and the Red is attached to the other leg of the sensing element. Some standard terminology would be Red to SENSE (+) one of the Black to SENSE (-) and the last Black to Ground.
https://www.omega.com/en-us/sensors-and-sensing-equipment/temperature/sensors/surface-sensors/p/SA1-RTD-series
Date published: 2023-12-13