Brand
Additional Features 1	Sunlight Readable
Baud Rate	300 to 19200
Calibration	Calibrated at the factory. Recalibration is recommended at least every 12 months
Category of Overvoltage	II
Category of Overvoltage Note	Installation overvoltage category II; local level with smaller transient overvoltages than installation overvoltage category III
Control Output	None
Data Interface	Modbus RTU
Data Interface Note	Protocol: Modbus RTU Meter Address/Slave ID: 1 – 247 Baud Rate: 300 to 19,200 bps Transmit Time Delay: Programmable between 0 and 199 ms Data: 8 bit (1 start bit, 1 or 2 stop bits) Parity: Even, odd, or none with 1 or 2 stop bits Byte-to-Byte Timeout: 0.01 to 2.54 seconds Turn Around Delay: Less than 2 ms (fixed)
Digital I/O Note	Channels: 4 digital inputs and 4 digital outputs per module System: Up to 2 modules for a total of 8 inputs and 8 outputs Digital Input Logic: High: 3 to 5 Vdc Low: 0 to 1.25 Vdc Digital Output Logic: High: 3.1 to 3.3 Vdc Low: 0 to 0.4 Vdc Source Current: 10 mA maximum Sink Current: 1.5 mA minimum +5 V Terminal: To be used as pull-up for digital inputs only
Display Color	Red
Display Size	15 mm (0.60 in)
Display Type	6 Digit Dual - Line -Sunlight Readable
Display Type Note	Both displays are 6 digits (-99999 to 999999), red LEDs with leading zero blanking Upper Display: 15 mm (0.60") high Lower Display: 12 mm (0.46") high Display Intensity: 8 intensity levels Display Update Rate: 5 per second Overrange: Display flashes 999999 Underrange: Display flashes -99999 Display Assignment: The upper and lower displays may be assigned to PV1, PV2, PCT (percent), max/min, alternate max and min, set points, units (lower display only), or Modbus input
Electrical Connection	Screw Terminal
Electrical Connection Note	Removable screw terminal blocks accept 12 to 22 AWG wire, RJ45 for external relays, digital I/o, and serial communication adaptors
Enclosure Material	Plastic
Enclosure Ratings	IP65, NEMA Type 4X
Form factor	1/8 DIN
Functions	Noise Filter: Programmable from 2 to 199 (0 will disable filter) ;Filter Bypass: Programmable from 0.1 to 99.9% of calibrated span ;Cyber Security: 3 programmable passwords restrict modification of programmed settings; Pass 1: Allows use of function keys and digital inputs; Pass 2: Allows use of function keys, digital inputs and editing set/ reset points; Pass 3: Restricts all programming, function keys, and digital inputs
Fuse Rating	5 A delayed
Height	62 mm
Input Type	Current, Voltage
Input Type Note	Input: Field selectable: 0 to 20 mA, 4 to 20 mA, ±10 Vdc (0 to 5, 1 to 5, 0 to 10V), MoDbuS PV (slave) Accuracy: ±0.03% of calibrated span ±1 count, square root and programmable exponent accuracy range: 10 to 100% of calibrated span Temperature Drift: 0.005% of calibrated span/°C max from 0 to 65°C ambient, 0.01% of calibrated span/°C max from -40 to 0°C ambient Signal Input Conditioning Function: Linear, square root, programmable exponent, or round horizontal tank volume calculation Multi-Point Linearization: 2 to 32 points for PV or PV1; 2 to 8 points for PV2 (dual-scale level feature) Programmable Exponent: 1.0001 to 2.9999 Low-Flow Cutoff: 0 to 999999 (0 disables cutoff function) Decimal Point: Up to 5 decimal places or none: d.ddddd, dd.dddd, ddd.ddd, dddd.dd, ddddd.d, or dddddd Calibration Range: 4 to 20 mA: Minimum span; input 1 and Input 2: 0.15 mA ±10 V: Minimum span; input 1 and 2: 0.10 V An Error message will appear if input 1 and input 2 signals are too close together Input Impedance: Voltage Ranges: Greater than 1 MΩ Current Ranges: 50 to 100 Ω (depending on resettable fuse impedance) Input Overload: Current input protected by resettable fuse, 30 Vdc max; fuse resets automatically after fault is removed
Isolation	4 kV input/output-to-power line; 500 V input-to-output or output-to-P+ supply
Length	143 mm
Memory	Non-Volatile Memory : All programmed settings are stored in non-volatile memory for a minimum of ten years if power is lost
Mounting	1/8 DIN panel cutout required: 92 x 45 mm (3.622 x 1.772"); two panel mounting bracket assemblies are provided
Normal Mode Rejection	Greater than 60 db at 50/60 Hz
Number of Inputs	1
Operating Temperature, Max	65 °C
Operating Temperature, Min	-40 °C
Output Configurations	None
Programmable Functions	Filter Bypass, Noise Filter, Security
Programming	4 front panel buttons, digital inputs, PC and software, Modbus registers, or cloning using copy function
Relative Humidity	0 to 90% non-condensing
Sampling Rate	5 Hz (5 updates/second)
Storage Temperature, Max	85 °C
Storage Temperature, Min	-40 °C
Supply Power Note	85 to 265 Vac 50/60 Hz, 90 to 265 Vdc, 20 W max, or jumper selectable 12/24 Vdc ±10%, 15 W max Isolated Transmitter Power Supply: 24 Vdc ±5% @ 200 mA max (standard), (12/24 Vdc powered models rated @ 100 mA max); 5 or 10 Vdc @ 50 mA max, selectable with internal jumper J4
Supply Power Type	DC
Supply Voltage	12 to 24 Vdc
Tightening Torque	Screw terminal connectors: 5 lb-in
Weight	269 g
Width	119 mm
Wire Gauge	22 to 12 AWG
Voir toutes Spécs Montrer moins

PDF et manuels

DP6000_spec DP6000 View More

View Less

Conformité

View Less

Reviews

Afficher les notes et les avis

0,0

(0)