Bienvenue sur notre nouveau site Web, vous avez rencontré un problème ou un bug? Veuillez le signaler ici
OM-NET-1608
8-Channel Multifunction Ethernet Data Acquisition Module
Spécifications du produit
<< Voir toutes les modèles de produits| Brand |
 |
| Alarm Note | Either or both outputs may be configured to go to defined values when an Ethernet connection with a host is established or lost |
| Analog I/O Note | Analog Input Note: ANALOG INPUT;A/D Converter Type: Successive approximation;ADC Resolution: 16-bits;Number of Channels: 4 differential (DIFF)/8 single-ended (SE), software-selectable;Input Voltage Range: ±10V, ±5V, ±2V, ±1V (software-selectable per channel);Absolute Max Input Voltage (CHx relative to AGND): ±20V max (power on), ±12V max (power off);Input Impedance: 1 GΩ (power on), 1200Ω (power off);Input Bias Current: ±10 nA;Input Bandwidth (All Input Ranges, Small Signal [-3 dB]): 700 kHz;Input Capacitance: 60 pf;Max Working Voltage (Signal + Common Mode); ±10V Range: ±10.2V max relative to AGND; ±5V Range: ±10.2V max relative to AGND; ±2V Range: ±9.5V max relative to AGND; ±1V Range: ±9.0V max relative to AGND;Common Mode Rejection Ratio (fIN = 60 Hz, All Input Ranges): 86 dB;Crosstalk (Adjacent Differential Mode Channels, DC to 10 kHz): -75 dB;Input Coupling: DC;Sample Rate: 0.019 Hz to 250 kHz, software-selectable;Trigger Source: TRIG (see External Trigger);Sample Clock Source: Internal A/D clock or external A/D clock (AICKI pin);Internal Sample Clock Stability: ±50 ppm;Internal Sample Clock Timebase: 80 MHz timer with 32-bit period (available frequencies are 80 MHz/integer period);Throughput: This is the typical throughput when the device and host are both connected by Ethernet to the same local network; the throughput can vary significantly if a wireless connection is involved or data is sent over the internet and is not guaranteed; Software Paced: 1000 to 5000 S/s type, on local network; Hardware Paced: 250 kS/s max;Channel Gain Queue (Up To 8 Elements): Software-selectable channel and range for each queue element;Warm-Up Time: 15 minutes min;Noise Performance: For the peak to peak noise distribution test, a differential input channel is connected to AGND at the input terminal block, and 16384 samples are acquired at the maximum rate available at each setting;Settling Time: Settling time is defined as the accuracy that can be expected after one conversion when switching from a channel with a DC input at one extreme of full scale to another channel with a DC input at the other extreme of full scale; both input channels are configured for the same input range;Analog Ouput Note: ANALOG OUTPUT;Number of Channels: 2;Resolution: 16-bits;Output Ranges (Calibrated): ±10V;Output Transient; Powered On; Duration: 5 ms; Amplitude: 2V p-p; Powered Off; Duration: 400 ms; Amplitude: 10V p-p;Differential Non-Linearity (16-bit Monotonic): ±0.35 LSB typ, ±1 LSB max;Output Current (AOUTx Pins): ±3.5 mA max (leave unused AOUTx output channels disconnected);Output Coupling: DC;Power On and Reset State: DACs cleared to uncalibrated zero-scale: 0V, ±50 mV unless the alarm function is enabled for the output; AOUTx defaults to 0V whenever the device is powered on or a reset command is issued to the device, unless the alarm functionality is enabled for the output;Alarm Functionality: Either or both outputs may be configured to go to defined values when an Ethernet connection with a host is established or lost;Slew Rate: 5V/µs;Throughput (Software Paced): 1000 to 5000 S/s typ, on local network. This is the typical throughput when the device and host are both connected by Ethernet to the same local network. The throughput can vary significantly, and typical throughput is not guaranteed if a wireless connection is involved or data is sent over the internet;Calibrated Absolute Accuracy (Analog Output);Range: ±10V;Absolute Accuracy: (±18.7 LSB);CALIBRATED ABSOLUTE ACCURACY COMPONENTS (ANALOG OUTPUT);Range: ±10V;% of Reading: ± 0.024;Offset: ±2.2 mV;Offset Tempco: 30.1 µV/°C;Gain Tempco: 13.2 ppm of range/°C;Relative Accuracy (Analog Output);Range: ±10V;Relative Accuracy (INL): ±4.0 LSB typ;ANALOG INPUT/OUTPUT CALIBRATION;Recommended Warm-Up Time: 15 minutes min;Calibration Method: Factory;Calibration Interval: 1 year (factory calibration) |
| Configuration Parameters | User-Configurable Input/Output |
| Data Interface | Ethernet |
| Data Interface Note | Ethernet Type - 100 Base-TX, 10 Base-T;Protocols Used: TCP/IP (IPv4 only), UDP;Network Ports Used: UDP:54211 (discovery), UDP:6234 (bootloader only), TCP:54211 (commands), TCP:54212 (scan data);Network IP Configuration: DHCP + link-local, DHCP, static, link-local;Network Name: E-1608-xxxxxx, where xxxxxx are the lower 6 digits of the device MAC address;Network Name Publication: By NBNS (responds to b-node broadcasts, therefore only available on the local subnet);Ethernet: 10/100 Mbps, auto-negotiated;Network Factory Default Settings;"Factory Default IP Address: 192.168.0.101;Factory Default Subnet Mask: 255.255.255.0 ;Factory Default Gateway: 192.168.0.1;Factory Default DHCP Setting: DHCP + link-local enabled";Network Security;"Security Implementation: TCP sockets are not opened unless application sends the correct PIN code (stored in non-volatile memory, may be changed by user, default value 0000);Number of Concurrent Sessions: 1;Vulnerabilities: TCP sequence number approximation vulnerability";Factory Reset Button;Used to reset the network configuration settings to the factory default values;Ethernet Cable Length, Max: 100 m;Configuration Method: Independently configured;Output Configuration: Digital: Independently-configured for input or output |
| Digital I/O Note | DIGITAL INPUT/OUTPUT Digital Type: 5V TTL input/advanced BiCMOS output Number of I/O: 8 Configuration: Independently-configured for input or output Pull-Up Configuration: All pins pulled up to 5V using 47 K resistors (default); can be changed to pull-down using an internal jumper Digital I/O Transfer Rate (System-Paced): 100 to 5000 port reads/writes or single bit reads/writes per second typ, on local network. This is the typical throughput when the device and host are both connected by Ethernet to the same local network. The throughput can vary significantly, and typical throughput is not guaranteed if a wireless connection is involved or data is sent over the internet. Alarm Functionality: Any combination of DIO bits may be configured to become outputs and go to defined values when an ethernet connection with a host is established or lost Power On and Reset State: All bits are input unless the alarm functionality is enabled for them Input High Voltage Threshold: 2.0V min Input High Voltage Limit: 5.5V absolute max Input Low Voltage Threshold: 0.8V max Input Low Voltage Limit: -0.5V absolute min, 0V recommended min Output High Voltage: 3.8V typ at no load, 3.0V min (IOH = -3 mA), 2.0V min (IOH = -32 mA) Output Low Voltage: 0.15V typ at no load, 0.55V max (IOL = 64 mA) Power On and Reset State: Input;Cross talk: -75 dB;Pulse Width: Trigger Pulse Width: 1 μs min;Schmitt Trigger Hysteresis: 1.01V typ, 0.6V min, 1.5V max |
| Digital Input | Digital: Low = 0 Vdc |
| Digital Output | (AOUTx Pins, ±3.5 mA max |
| Electrical Connection | Screw Terminal |
| Frequency Input Range | 10 MHz |
| Height | 29 mm |
| Input Bias Current | ±10 nA |
| Input Capacitance | 60 pf |
| Input Configuration | Connected Software |
| Input Type | Voltage, Digital |
| Input Voltage Note | Absolute Maximum Input Voltage: Analog: ±20V max (Power On), ±12V max (Power Off) |
| LED Indicators | LED Displays;Power LED (Top),Activity LED (Bottom); Ethernet Connector LEDs; Left, Green: Link/activity indicator,Right, Yellow: Speed indicator |
| Length | 117.9 mm |
| Memory | Non-Volatile |
| Number of Channels, Input | Analog: 4 DIFF / 8 SE, Digital: 8, Counter: 1 |
| Number of Channels, Output | Analog: 2, Digital: 8 |
| Operating Temperature, Max | 55 °C |
| Operating Temperature, Min | 0 °C |
| Output Resolution | Analog: 16-bits |
| Output Signal | Digital, Clock, Current, Voltage |
| Pull-down Resistor | 47 kΩ, GND |
| Pull-up Resistor | 47 kΩ |
| Relative Humidity | 0 to 90% RH non-condensing |
| Sampling Rate | 0.019 Hz to 250 kHz (0.019 to 250,000 updates/second) |
| Slew Rate | 5 V/μs |
| Stability | Internal Sample Clock: ±50 ppm |
| Storage Temperature, Max | 85 °C |
| Storage Temperature, Min | -40 °C |
| Supply Current | 330 mA |
| Supply Power Note | External Power Supply: 5V, 1A (via included AC adaptor) Supply Current (Quiescent Current): 330 mA typ (this is the total quiescent current requirement for the device that includes the LEDs and does not include any potential loading of the digital I/O bits, +VO terminal, or the AOUTX outputs), 710 mA max including all external loading User Output Voltage Range (Available at +VO Terminal): 4.40V min to 5.25V max, assumes supplied AC adaptor is used User Output Current (Available at +VO Terminal): 10 mA max |
| Supply Voltage | 5 Vdc |
| Voltage Measurement Range | ±10V, ±5V, ±2V, ±1V |
| Warm Up Time | 15 min |
| Weight | 0.4 kg |
| Width | 82.8 mm |
| Wire Gauge | 18 to 16 AWG |
| Voir toutes Spécs | |
PDF et manuels
Logiciels et pilotes
Afficher les notes et les avis