Bienvenue sur notre nouveau site Web, vous avez rencontré un problème ou un bug? Veuillez le signaler ici
UHF-HFS-Series
Heat Flux Sensors for Heat Transfer Measurements
Modèles en stock
- HFS-5 Economical sensor for use in R&D heat transfer measurements and thermal systems evaluation
- HFS-6 Larger sensor for use in buildings thermal evaluation and higher sensitivity
- UHFS-09 Larger sensor, highest sensitivity and waterproof for use in geothermal studies
- HFS DAQ as the accessory of HFS series, low-cost data acquisition system to accurately measure the signals outputted from HFS heat flux sensors and their integrated thermocouples
UHF-HFS-Series
Depuis
C$
560.27
Modèles en stock
L'aperçu du produit
- Heat Flux Range ± 150 kW/m²
- Number of Wires 4
- Process Temperature, Max 120 °C
- Temperature Sensor Type Thermopile
Omega's Heat Flux Sensors provide accurate readings, high sensitivity with fast response times. The sensors are rugged and economical. They are ideal for R&D applications ranging from aerospace, industrial processes to building sciences applications. Do not forget to get your Omegatherm high temperature and high thermal conductive paste for mounting.
PDF et manuels
Afficher les notes et les avis
What data logger can be used with your heat flux sensors?
Thank you for the inquiry. We have the new Layer N system with SP-016-1. Part of the modular Layer N system;
https://www.omega.com/en-us/layer-n/smart-probes/p/SP-016-Series
Best regards
OMEGA
Date published: 2020-10-06
If I need to calculate the total heat power through HFS-5, should I multiply the measured heat flux with sensor area (6.5cm2) or total area (9.2cm2)?
Hi Han2021
Thank you for the inquiry. Please forward this question to TEMP@OMEGA.CON.
Best regards
OMEGA
Date published: 2022-05-17
What is the maximum sampling rate for the HFS-5?
Hi Trevor C
Thank you for the inquiry. Sample rate would be determined by the instrumentation used. Response time of the sensor is 0.6 seconds as noted on the data sheet.
Best regards
OMEGA
Date published: 2022-05-17
What is the output voltage range for HFS5?
Hi Daniel18
Just under 1 mv at max heat flux. You'll need a meter with micro volt level resolution.
Best regards,
OMEGA
Date published: 2021-12-23
Can the HFS-5 heat flux sensor be used outside in the weather?
Hi Trevor42
Thank you for the inquiry. This sensor is not suitable for outdoor weather conditions.
Best regards,
OMEGA
Date published: 2022-01-24
What is the core material (dark brown) in the HFS-5 sensor and whether it distributes the heat laterally?
Hi Han2021,
Please forward this question over to our temperature group for review; TEMP@OMEGA.COM
Best regards
OMEGA
Date published: 2022-05-17
we are using the HFS-5 Heat Flux+ T type Thermocouple sensor and the HFS-DAQ. I need to add 8' of length to the wire leads of the sensor to reach our test location. Do you sell these as integral cables? if not, can you suggest extension cables? Thanks
Hi Keithgm,
Thank you for the inquiry. We d not offer integrated cable unfortunately.
For the thermocouple side;
You'll need type T extension wire similar to https://www.omega.com/en-us/temperature-measurement/temperature-wire-and-cable/thermocouple-wires/extt-tx-wire/p/EXTT-T-24-25.
For the heat flux side you can use 2 conductor instrumentation wire (copper).
Best regards
OMEGA
Date published: 2022-08-23
Hi, I am following up on my question about the output voltage. I need to make sure that my data logger is scaled properly. This sensor has a heat flux range of +/- 150 kW/m^2. Does +/- 150 kW/m^2 correspond to +/- 1 mV respectively? Thank you.
Hi Daniel8,
Please forward your request to TEMP@OMEGA.COM for assistance in scaling a datalogger or other meter.
Best regards,
OMEGA
Date published: 2023-04-25